Multimedia

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - couch

Pages: 1 2 3 4 5 [6] 7 8 9 10 11 ... 37
76
The Lounge / Post Your Guns
« on: April 10, 2012, 05:44:52 PM »

77
The Lounge / Post Your Guns
« on: April 09, 2012, 05:06:00 PM »
I plan to pick one of those up, or make one myself.

78
The Bike Shop / Spanish BB Length
« on: April 09, 2012, 12:40:46 PM »
Unless its been changed, the bearing seat depth is called out at 10mm, if I remember correctly. So taking that into account, the spacer is the correct width. Are your bearings flush with the shell or are they sitting below the face by 1mm?

What did you use to install the bearings?

79
The Lounge / Post Your Guns
« on: April 08, 2012, 08:44:33 PM »

80
The Lounge / Post Your Guns
« on: March 31, 2012, 11:58:57 AM »
Condition One

81
The Lounge / Post Your Guns
« on: March 26, 2012, 12:35:05 AM »
What the hell is this abomination?!




82
The Lounge / Post Your Guns
« on: March 24, 2012, 11:11:07 PM »
Quote from: Rick James;3541974
POF making them wouldn't surprise me. The AR15.com billet lower is the exact same as the Magpul, too.

POF doesn't make their own parts. Quentin used to mill them, if I'm not mistaken, but as of right now they do not have a mfg. AR15.com licensed the "design" form Magpul, and is THE same lower aside from engraving/logos. Magpul made their own lowers in house.

Most badass lower around is the AXTS AX556.

http://axtsweapons.com/products/AX556#


83
The Lounge / Post Your Guns
« on: March 14, 2012, 01:31:52 PM »
I was wondering the same thing. They definitely don't work the same as a standard bushings. Surprised they didn't use bull barrels instead.

84
The Lounge / Post Your Guns
« on: March 06, 2012, 08:25:33 PM »
From all the research I've done and @ tea eff letters I've read, the lower must have specific engraving in order to sell.

The gray area is what defines as a manufacturer. That's what nobody can figure out. How many lowers being sold considers you a manufacturer, how often and so on.

85
The Lounge / Post Your Guns
« on: March 05, 2012, 11:50:57 PM »
I can legally make my own lowers as long as there is no intent to sell. And if I do want to sell I need to engrave a little info and go thru an FFL as a PPT.

This was an 80% TM Lower. Milled the FCG and drilled the selecter and trigger holes.

86
The Lounge / Post Your Guns
« on: March 05, 2012, 03:19:36 PM »

87
The Lounge / Post Your Guns
« on: February 21, 2012, 03:03:23 PM »
NME tools will be back in stock next week.


88
The Lounge / Post Your Guns
« on: February 20, 2012, 06:08:04 PM »
Your barrel is finished. PO is closed today so its going out tomorrow.

89
The Lounge / Post Your Guns
« on: February 20, 2012, 05:03:27 PM »
Quote from: smalley;3530778
Americans are insane why does it matter if you can't carry a gun in a coffee shop?


Should I lock it up outside with my bike?

I'm sure you're referring to the Starbucks issue. Starbucks is pro 2A, not anti. Its not an issue with us complaining we can't do it, its an issue with the Brady bunch complaining we can. Huge huge difference.

90
The Lounge / Post Your Guns
« on: February 20, 2012, 01:28:03 PM »
Blended MSH/Magwell to frame.





Pages: 1 2 3 4 5 [6] 7 8 9 10 11 ... 37
-->

Tell them " Sheepdog sent you", for a little something special

Click this image for a little something special
Hello