Messages

121

The Lounge / Post Your Guns

« on: November 21, 2011, 06:49:57 PM »

As of right now I plan to remove the trigger guard hook, finger groove and knurling on the front strap. I may make a new tumblr dedicated to this build... may just put it up on the Zodiac one. Regardless, I'll post progress in this thread as well.

122

The Lounge / Post Your Guns

« on: November 21, 2011, 05:58:49 PM »

You want a bobtailed MSH made from scratch or you want the work done?

I don't have an FFL yet so I can't work on your frame without you here.

123

The Lounge / Post Your Guns

« on: November 21, 2011, 05:24:15 PM »

Definitely will be a fun project. In just thinking, I already have two others on their way and I need to buy parts for all three... my pocket hurts already.

124

The Lounge / Post Your Guns

« on: November 21, 2011, 04:21:01 PM »

At least your open to them and not in here bashing us.

125

The Lounge / Post Your Guns

« on: November 21, 2011, 04:03:42 PM »

Well, this just came in the mail... aluminum 1911 casting. Building up an Officer length grip with Commander length slide. Something as light as possible, for carry.

 

126

The Lounge / Pets thread.

« on: November 21, 2011, 02:14:22 PM »

127

The Lounge / Post Your Guns

« on: November 16, 2011, 06:48:58 PM »

Any word on that project we talked about a few months ago?

128

The Lounge / Post Your Guns

« on: November 15, 2011, 06:59:09 PM »

Couch, is that an 80% lower? Meaning you trim out the center yourself. Lower is lookin' good so far. I love my BAD lever!

Yeah, its a Quentin Laser/Defense billet 80% lower. Milled both trigger pin holes, Selecter hole and FCG pocket. This Selecter feels so much better than the stock one!

My new Kimber Warrior.  Paid in February, I got it this week.

What's up with the finish on the front of the slide?

129

The Lounge / Post Your Guns

« on: November 02, 2011, 10:43:19 PM »

They aren't necessary, but there isn't really a negative effect they have on the system (aside from needing a wrench to remove the FCG). A lot of people talk about pins walking out, but the springs should keep them in place. These are just an added bonus, if anything.

130

The Lounge / Post Your Guns

« on: November 02, 2011, 10:01:19 PM »

BAD-ASS-ST came in today!

131

The Lounge / Post Your Guns

« on: November 01, 2011, 12:00:14 AM »

Just ordered a Battle Arms Development - Ambi Safety Selecter, finally.
BAD-ASS

Ordered the 45 degree Short Throw version with a Standard lever on the thumb side for a high ride similar to my 1911 and a Short-Thin for the opposite side.



http://www.youtube.com/watch?v=QGYghk5hwTk

132

The Lounge / What have you made?

« on: October 28, 2011, 05:04:29 PM »

Prototype Animal Sprockets 25, 27 & 28

133

The Lounge / Post Your Guns

« on: October 25, 2011, 09:18:44 PM »

134

The Lounge / Post Your Guns

« on: October 25, 2011, 09:07:19 PM »

I have a UBR and I still cannot figure out what the buttons on the side do!

I read all about them, on forums and the directions.  And I push the buttons in, preset and reset but nothing fucking happens.

If anyone know wtf they do or how they work, I would appreciate the knowledge.

Mine just got here. You need to set the preset with the small screw inside the main body on the bottom. Take the stock apart and you'll see it on the bottom. Once this is set to where you want it, simply pulling the release latch will bring you back up until that preset spot. If you need to go further back you press the left side preset button to go further back.

135

The Lounge / Post Your Guns

« on: October 25, 2011, 03:55:01 PM »

I have a UBR and I still cannot figure out what the buttons on the side do!

I read all about them, on forums and the directions.  And I push the buttons in, preset and reset but nothing fucking happens.

If anyone know wtf they do or how they work, I would appreciate the knowledge.

Left side is the preset button. Right side is the remove.

 http://www.youtube.com/watch?v=MrhFJA7LIjY