Multimedia

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - joelite44

Pages: [1] 2 3 4 5 6 ... 9
1
The Lounge / Re: Where is everyone at in life?
« on: June 20, 2020, 08:11:11 AM »
I too am interested in bluemeate  status. Also I follow rusty on instagram he goes by pedalgrinds.

2
The Bike Shop / Re: converting bike with gears to single speed?
« on: August 01, 2019, 05:39:55 PM »
i cleaned and greased the posts but the brake will not hold even tension on both arms or center itself properly.

for a conventional V-brake, there should be 3 tiny holes on the frame right next to the v-brake lug, and you should see that the coil spring 'slots' into one of the three. they are for you to adjust tension. by slotting the coil spring into different holes you can get different amount of absolute tension, or tension relative to the opposite brake arm. that should give you a set up that works good enough for the arms/ brakepads to stay away from the rim when you're not pulling the brake lever

Place the brakes on the middle hole and bolt it to the frame. undo the little screw that tensions the v brake spring and stretch it out.

This is the same spring that is held to the middle hole. Do this so the v brake can have more tension.

Lastly tighten the screw in slightly and which ever brake  (Left or right) needs more tension, undo the contrary screw to carry it in or out.

Sorry for sounding retarded.

3
The Bike Shop / Re: converting bike with gears to single speed?
« on: July 28, 2019, 02:21:43 PM »
If your going to carry a trailer you might as well have gears.

Watch some youtube videos and get these derraileurs going its nothing a few years of experience won't fix.

4
The Bike Shop / Fat Tires (for the rear)
« on: July 23, 2019, 04:12:49 PM »
Hello kids,

I don't ride that much but it seems that im only going smaller on tires for my rear wheel. Why? A few pointers for the smaller sized tire are:

No need to upgrade your frame choices.

Most new frames now a days come with the 2.35 rear tire option. But I don't spend 389.99 bucks on a new frame. I just stick with the classics.

Your rear hub will last longer THIS

Am I right? Im not trying to prove anyone wrong but does it make sense a smaller tire weighs less than a big fat tire and therefor reduces the impact to your wheel hub?

I feel like kids now a days go through hubs and parts faster than we used to.

What other points do you approve for running smaller tires on the rear? Or do you already run the big fat tire.

5
The Lounge / Re: Adam22
« on: November 08, 2018, 10:08:04 PM »
gnar_rider you are pretty late on this.

Hence the thread Bmxers are still mad Adam 22 ripped BMX a new bum hole.

6
The Bike Shop / Re: New hub what’s BG recommend if anyone’s out there
« on: October 07, 2018, 12:30:21 PM »
Clutch Freecoaster.

It is very much the same as a ratchet but uses freecoaster internals.

All other specs besides helicoil inside the axle are the same.

7
The Bike Shop / Re: 24mm cranks
« on: July 25, 2018, 06:00:09 PM »
i see how 100 dollar cranks can be atractive. However you can clearly see how bearings on 19 mm cranks get murdered after a few years of use. Can't say the same about 24 mm cranks and smaller bearings.

8
The Bike Shop / Re: 24mm cranks
« on: July 24, 2018, 07:30:45 PM »
im looking into buying some 24mm fit indent cranks.
theyre on sale for cranks + sprocket for $150 and theyre overall about 2oz lighter than my twombolts.
but my main concern is that the they have been out for a while, no one is buying them and they will soon stop producing 24mm mid bb's
should i buy them anyways?

People always say how the bearings don't last.

9
The Lounge / Re: T-shirt company
« on: June 25, 2018, 04:12:36 PM »
You actually went to prison? We need details and stories....
No not prision just a comissary if you can call it. You get caught drunk and driving and you either pay a fine to leave or pay up with staying 48 hours. You still have to pay for your car impoundment.

11
pictures of the spline drive sprocket?

12
The Lounge / Re: T-shirt company
« on: June 13, 2018, 05:24:47 PM »
I had a t-shirt company like 14 years ago (boy am I old...).

How it sells and what designs and types of shirts that will work depend on what market you go for.
Based on the type of shirt and design I would say it could work if you want to sell it to BMXers or people in similar groups that you hang out with.
Sales would best work if you sell it at jams or similar.

If you wanna sell it locally at a store or similar I would recommend a different type of shirt depending on how people dress where you live.

Thanks for your input. I need to aim my market since this is a company fueled by bmx only.

13
The Bike Shop / Re: ebike Bmx commuter
« on: June 07, 2018, 12:35:02 PM »
Wait until 2200 when these things become regular.

Or spend 900 bucks on a used old motorcycle. Fix it, Fall in love with it, sell it, buy another and repeat.

Until you can carry your fat girlfriend on cross country rides.



You are welcome.

14
The Lounge / Re: T-shirt company
« on: June 01, 2018, 11:00:36 AM »
Second batch was 24 shirts, XXL, XL, L, M & S

Only one has sold, to my riding buddy. I still havn't defined which niche I will be targeting.

"Recio" merely describes the personality of a ADHD child which has no control of its actions, It is living with whatever happens. If you comprehend this you will like our brand. If you have a cookie cutter personality you most likely won't relate.

Pages: [1] 2 3 4 5 6 ... 9
-->

Tell them " Sheepdog sent you", for a little something special

Click this image for a little something special