Author Topic: Post Your Guns (Read 2797170 times)

nitromors · « **Reply #2835 on:** November 21, 2011, 06:41:40 PM »

Quote from: couch;3499281

Well, this just came in the mail... aluminum 1911 casting. Building up an Officer length grip with Commander length slide. Something as light as possible, for carry.

i am jacks gruesome sense of envy,

keep updating....

couch · « **Reply #2836 on:** November 21, 2011, 06:49:57 PM »

As of right now I plan to remove the trigger guard hook, finger groove and knurling on the front strap. I may make a new tumblr dedicated to this build... may just put it up on the Zodiac one. Regardless, I'll post progress in this thread as well.

couch · « **Reply #2837 on:** November 21, 2011, 06:53:25 PM »

The frame is basically an Olympic Arms raw casting...

http://olyarms.net/index.php?page=shop.product_details&flypage=flypage.pbv.v8.tpl&product_id=128&category_id=9&option=com_virtuemart&Itemid=5&vmcchk=1&Itemid=5

Rick James · « **Reply #2838 on:** November 21, 2011, 07:04:32 PM »

Should look a lot better with those frame mods. I'm not too keen on it the way it currently sits.

couch · « **Reply #2839 on:** November 21, 2011, 07:52:07 PM »

I completely agree.

Rusty Shackleford · « **Reply #2840 on:** November 21, 2011, 09:19:45 PM »

Quote from: Birdmane;3499268

I know nothing about vests.

I need a tan/coyote vest with plate holders. I plan to have molle ar mag holders, glock mag holders, someplace to put shotgun rounds, a sling attachment and a glock holster.

What do I get?

blackhawk serpa holster for the glock, and with vests it depends on what you want to spend can go the cheap route and grab a condor or more expensive and go with one of blackhawks or tactical tailor.

http://www.blackhawk.com/product/STRIKE-SERPA-Holster-for-Beretta,782,1416.htm
i got the same holster for my g17

Birdmane · « **Reply #2841 on:** November 22, 2011, 01:47:16 AM »

I want a Dan Wesson Guardian 9mm...but dont want to dish out the 1k even with my discount.

I wish someone would make a bobtailed basic gun like a springer mil spec then Id just throw some novaks on there and call it a day.

Rick James · « **Reply #2842 on:** November 22, 2011, 01:58:50 AM »

Quote from: Birdmane;3499483

I want a Dan Wesson Guardian 9mm...but dont want to dish out the 1k even with my discount.

I was looking at them pretty hard a month or so ago but couldn't do it for the same reason. One of these days...

couch · « **Reply #2843 on:** November 22, 2011, 03:25:44 AM »

Quote from: Birdmane;3499483

I want a Dan Wesson Guardian 9mm...but dont want to dish out the 1k even with my discount.

I wish someone would make a bobtailed basic gun like a springer mil spec then Id just throw some novaks on there and call it a day.

Just buy an Ed Brown jig and bobtailed MSH. Its a pretty simple modification. I'll buy the tool off you if you go that route.

attactrl · « **Reply #2844 on:** November 22, 2011, 03:56:04 AM »

I want to get a Ruger P95 when I have the funds. Expecially after that bus bikerack situation went down.

(don't think I would have shot him, but it prolly would not have happened like if they knew I had one)

couch · « **Reply #2845 on:** November 23, 2011, 01:26:03 PM »

farva · « **Reply #2846 on:** November 23, 2011, 04:14:59 PM »

Quote from: couch;3500101

whaaaa! It lives!

couch · « **Reply #2847 on:** November 23, 2011, 05:12:24 PM »

BottleOpener
1911 Bushing Wrench
1/4" Broach
Standard Tip Screw Driver/Pry
Domestic 6Al/4VTitanium
5/32" Thick
2-1/4" x 1-7/16"
100% Made In The USA
Waterjet Blanks made by Defcon4

couch · « **Reply #2848 on:** November 23, 2011, 05:17:35 PM »

super_chief · « **Reply #2849 on:** November 23, 2011, 05:40:56 PM »

when can i order one?

Bikeguide.org - Bike maintenance for BMX'ers · « **Reply #2849 on:** November 23, 2011, 05:40:56 PM »

Author Topic: Post Your Guns (Read 2797170 times)

Bikeguide.org - Bike maintenance for BMX'ers