Multimedia

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - I <3 Gore.

Pages: [1] 2 3
1
The Lounge / Re: 15 Years on the forum
« on: July 27, 2017, 05:23:43 PM »
Been lurking since 01' registered since 03' and due to circumstances I don't feel like describing had to ditch my old account for this one in 05'.

Fuck I am old, but I still shoot footy with the old crew and ride pretty regularly at 32yo.

3
The Lounge / Re: Dave Mirra Dead
« on: February 04, 2016, 07:33:01 PM »
That's nuts. Didn't seem like the type you know?

no one ever seems like the type, hard times hit hard. With Collin it was his partner leaving him, could it be the same in this case?

4
The Lounge / Re: Dave Mirra Dead
« on: February 04, 2016, 06:48:02 PM »
I was just about to post this! what the fuck man, why do legends always have to kill themselves?

5
The Lounge / Re: New Star Wars trailer.
« on: November 30, 2014, 03:16:55 AM »
ugh it looks shit. It just feels too plastic.

6
The Lounge / Re: Age?
« on: November 22, 2014, 02:20:30 PM »
29, 30 in two months. Found this site in 2002 reading the brake adjustment guide.

7
The Bike Shop / Re: made a few sprockets
« on: November 21, 2014, 07:16:27 PM »
How much for a dick sprocket?

Twenty-five Schmeckles.

8
The Bike Shop / Re: Oil Slick / "jet fuel", really ?
« on: November 21, 2014, 07:14:54 PM »
Yeah, if it's made out of Au, $300 extra is a bargain, but it's probably too heavy to really ride.

2-Hip Pork what?

9
The Bike Shop / Re: I'm so bliiiiiiiind
« on: November 21, 2014, 07:13:13 PM »
The best BMX film ever was the film all over my balls after I fell into an oil-slicked puddle trying a bunnyhop over it.

this is either a severely intelligent bot or one of the most insightful bits of bmx related babble I have ever read.

10
The Bike Shop / Re: Keychain help
« on: November 19, 2014, 08:36:54 PM »


better pic of both failed plate and pin thread. Question is, which went first since the were on separate links.

11
The Bike Shop / Re: Keychain help
« on: November 19, 2014, 02:22:40 AM »
Check your chain alignment, try to get it as straight as possible.

This is what I hate about frames these days, I have to risk scraping the teeth of my sprocket on the chainstay to get proper alignment.

12
The Bike Shop / Re: Keychain help
« on: November 17, 2014, 07:30:43 PM »

Sorry to hear that. Obviously a blurry photo isn't going to tell the full story here but if you think there was any kind of design or manufacturing fault then please send it back for warranty. If it has a huge donk in it from hitting something then that is likely the cause (and obviously the threaded pin cant pull out like a normal rivet so some sort of break is expected) but if not then it would be good to have it back and try to work out the cause.

I hope this makes sense and seems reasonable.

:)
G.

I'll send it and the breaker back to you guys, from what I can gather-ie looking at the bits that broke-it seems like the threads broke on the 1/2 link, which wrenched on the adjacent riveted link breaking said link. I'll try to take a better pic later.

13
The Bike Shop / Re: Keychain help
« on: November 17, 2014, 02:11:25 AM »
I'd also like to add that your "proprietary" chain breaker does not work correctly with the hollow pin chain. The plate stop has too small of a hole and does not allow the pin through, pretty suck because the breaker BROKE without it.

14
The Bike Shop / Re: Keychain help
« on: November 15, 2014, 02:31:01 PM »
I am sorry if you are having problems, how many times have you had this happen? If you in any way think that your chain may be faulty then please contact warranty and we will be very happy to look at it. If you have previously ordered a masterlink kit then I would have thought we could sort something out or cut you a deal on the next one.

The keychain has been in development for a very very long time, and generally speaking we have seen very very few JRA type incidents, there are no modifications or V2's in the works. (though we are looking at doing slightly longer ones for non-BMX use). 

I hope this sounds reasonable.

:)
G.

Honestly, I had no problems with it up until now. I don't ride pegs, and ride a full guard sprocket. It was literally out of the blue and I can't exactly pinpoint which failed, the master-link or the link next to it.



the threads on the master-link pin completely sheared off

15
The Lounge / Possible Freecoaster bearing?
« on: November 15, 2014, 03:32:37 AM »
This is purdy nutty, such an awesome bearing design.

http://www.gosocial.co/mysterious-box/?v=1


Pages: [1] 2 3
-->

Tell them " Sheepdog sent you", for a little something special

Click this image for a little something special
Hello