Multimedia

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - TheHouseProduct

Pages: [1] 2 3
1
The Lounge / Post Your Guns
« on: February 20, 2013, 04:27:16 PM »
Quote from: Cole;3633916
While we're on the subject of gear-queers, I need suggestions for a sling. No three points.

For rifle or shotgun?  I really like my Magpul sling for my rifles but the hook doesn't fit the loop on my GG&G shotgun sling mount.  I went with a cheap o mash hook sling that fit it.

2
The Lounge / Post Your Guns
« on: February 20, 2013, 09:42:22 AM »
Before everyone gets too down on playing soldier, have you tried playing soldier? It's pretty sweet. :-)
Just have an understanding that you are living out call of duty goober fantasies. I've taken slings and holsters and mag holsters and transitioned from primary to secondary etc etc and end up laughing my ass off having a good time. I look full retard but no one but the other retards have to know.

3
The Lounge / Post Your Guns
« on: February 19, 2013, 10:28:26 AM »

300BLK collection.
Single shot Savage bolt gun with a 4-14x on top.
13.5" AR with pinned flash hider for 16".
AAC Handi Rifle with Trijicon RMR.

4
The Lounge / Post Your Guns
« on: February 02, 2013, 04:08:25 PM »
Quote from: yacqueli;3629111
that all depends on how you run your gun. You shoot 556 or 223 out of your uppers?
No it doesn't. The bolt carrier of a blowback gun like 9mm hits the hammer way harder and faster than the comparatively slow bolt carrier of a 223 DI gun. It tends to make hammer pin holes in 9mm lowers elongate. Hence the heavier buffers and ramped bolts in 9mm guns.

5
The Lounge / Post Your Guns
« on: February 02, 2013, 01:23:54 PM »
Quote from: yacqueli;3629004
New frontier armory lower...

I don't suggest running that on anything bigger than 9mm upper. 223/556 uppers have been known to break them. I've seen 2 personally cracked from 556 upper use.
9mm is harder on lowers than 223.

6
The Lounge / Post Your Guns
« on: January 02, 2013, 03:20:39 PM »
Quote from: PabstBlueRibbon;3620134
how does it shoot? hows recoil?
Recoil is a tiny bit less than a pump gun. It had gas issues and will need to get some work done for reliability. Not uncommon with these guns.

7
The Lounge / Post Your Guns
« on: December 29, 2012, 06:53:18 PM »


AZ Saiga12. Blasting tomorrow.

I'm up to about 10 reloading presses. I reload about 15 calibers.

8
The Lounge / Post Your Guns
« on: November 29, 2012, 11:25:28 AM »
Quote from: Albie;3611285
I need something full size.


And what generation do you have?

I have brand new in box gen 3 G17 and G19.

9
The Lounge / Post Your Guns
« on: November 28, 2012, 08:47:33 PM »
Quote from: Albie;3611101
Who wants to trade me a Glock 17 for a Sig 1911?
I will. Pics of the 1911?

10
The Lounge / Post Your Guns
« on: November 27, 2012, 04:20:21 PM »
Quote from: couch;3610778
Why not just fit a 9mm slide/barrel on the 1911 you usually shoot? The grip angle and lack of similar controls isn't going to help with training.

Its going to be cheaper than a new gun, you won't have a ten day wait, you hate Glocks and while somewhat blasphemous (9mm 1911) you can shoot the 1911's more.
Are there drop in conversions? Do you need a ramped barrel to switch back and forth?

11
The Lounge / Post Your Guns
« on: November 27, 2012, 04:19:26 PM »
Quote from: yacqueli;3610770
yeah that 10 day wait thing isnt working for me anymore. but that is a good deal!
You working out of a shop or home?
My home

12
The Lounge / Post Your Guns
« on: November 27, 2012, 11:16:47 AM »
Quote from: gnar_rider;3610727
i want a springfield xd subcompact i think, opinions?
I didn't like mine at first but it's grown on me. The trigger sucks but I enjoy shooting it now.

13
The Lounge / Post Your Guns
« on: November 27, 2012, 11:15:22 AM »
Quote from: yacqueli;3610657
All this talk about 9mm.. Going to buy a glock 19 or 17 but not sure. Pretty much only going to be used for pistol class since I don't want to feed my 1911's
I'm an FFL in Orange County with some Glocks in stock for $475. PM if you're interested.

14
The Lounge / Post Your Guns
« on: November 25, 2012, 02:20:12 PM »
Quote from: BOUNCEHOUSE420;3609856
What About a barrel receiver flat 922r parts and a maglock or grip wrap? If I could build them that cheap id build 3!



Drew ive been eye fuckin a confederate navy replica bp revolver for a while... I want that fucker pretty bad
Barrels came with the kits back then. Receiver flat was $12. Ran a raddlock for a while then moved it to AZ.

15
The Lounge / Post Your Guns
« on: November 23, 2012, 06:03:35 PM »
I paid $80 for my Romanian kit. Machined my own bending jig and welded the trunions. I have a working AK for about $110. :-)

Pages: [1] 2 3
-->

Tell them " Sheepdog sent you", for a little something special

Click this image for a little something special
Hello