151
The Lounge / Re: What have you made?
« on: November 21, 2013, 07:17:06 PM »
what is your process?
Welcome, Guest. Please login or register.
Did you miss your activation email? April 20, 2024, 01:12:22 PM
Did you miss your activation email? April 20, 2024, 01:12:22 PM
| Multimedia |
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
152
The Lounge / Re: What have you made?
« on: November 18, 2013, 11:11:45 PM »
Made this Zero Clearance Insert for my tablesaw
153
The Bike Shop / Re: What did you do to your bike today? (v2)
« on: November 18, 2013, 08:58:07 PM »
I need a bottle of these 222's
Installed my springfields and dialed them in. Disappointed that I could not get my spoke mod straddle hanger to work. apparently the narps I have are just a hair bigger in diameter than the springfield will allow. Really happy with spring tension.
Installed my springfields and dialed them in. Disappointed that I could not get my spoke mod straddle hanger to work. apparently the narps I have are just a hair bigger in diameter than the springfield will allow. Really happy with spring tension.
154
The Bike Shop / Re: What did you do to your bike today? (v2)
« on: November 17, 2013, 07:59:11 PM »
It will be tight but it will work
155
The Bike Shop / Re: What did you do to your bike today? (v2)
« on: November 16, 2013, 01:52:11 AM »putting the stoppers back on, and found out evo 2's wont clear a fly 2.125 on an S&M stricker
Probably down to the boss spacing rather than the caliper, though switching out the pad spacing is often all it takes to get the space you need.
G.
G,
the tire was rubbing the arms off of the boss. No worries found out springfields fit the bill. Ordered up and ready to roll. I can post a pic of the tire rubbing if you want
156
The Bike Shop / Re: What did you do to your bike today? (v2)
« on: November 13, 2013, 05:23:16 PM »
putting the stoppers back on, and found out evo 2's wont clear a fly 2.125 on an S&M stricker
157
The Bike Shop / Re: What did you do to your bike today? (v2)
« on: November 08, 2013, 04:56:38 PM »
Blew my knee up last night. got a prescription for a custom brace this morning. Win Win in my book
158
The Lounge / Re: What have you made?
« on: November 06, 2013, 11:18:29 AM »So with that bottle opener, you open the bottle, the cap falls down a bit and then sticks in the area with the magnet on the back, right?
Yep, Pure Fucking Magic I tell you
159
The Lounge / Re: What have you made?
« on: November 06, 2013, 12:35:46 AM »All depends on the look you're going for. Poly can be a bit of pain to get to look nice but it can look really nice with a bit of work. What'd you use to apply the poly? Did you sand it and apply multiple coats?
used a rattle can. built up 3 coats then started sanding between coats. I started with some 400 and worked up to 0000 steel wool. I am impressed for the rattle can. just should that thought about other finishes out there/
160
The Lounge / Re: What have you made?
« on: November 05, 2013, 10:46:22 PM »That's awesome! I've seen a lot of people building these recently for some reason. I want tomake one!
They arent cheap I can tell you that. I averaged material out for 3 and it came out to like $32 dollars a piece. But I didnt have any scrap, or glue or the finishing stuff. Also stay away from poly, was not happy with its finish. Next one will be boiled linseed oil.
161
The Lounge / Re: What have you made?
« on: November 05, 2013, 10:13:33 PM »Is that magnetic?
yep. It is pretty sweet. holds like 52 caps or some crazy shit
162
The Lounge / Re: What have you made?
« on: November 05, 2013, 01:55:31 PM »
Just finished up 3 of these. One was for a silent auction the other as gifts. Not to bad as I have not woodworked in the last 4 years.
163
Sell and Swap / Re: Trusted/Un-trustworthy sellers
« on: November 04, 2013, 06:12:25 PM »
Lowkey: worked out a quick deal, sent the cash fast. Easy to work with. A+
Milhous: Yet again easy to work with. Sent cash fast
Stoked: Smooth and easy to work with
worzian: awesome dude easy to work with. sent cash fast
Milhous: Yet again easy to work with. Sent cash fast
Stoked: Smooth and easy to work with
worzian: awesome dude easy to work with. sent cash fast
164
The Bike Shop / Re: What did you do to your bike today? (v2)
« on: November 02, 2013, 10:26:25 PM »sold off most of my T1 today. It was a semi sad dayThis is what it sounds like when doves cry
I am getting older, I dont need 3 bikes any more. It is gonna fund my final bike I wanna build
Rode Irving skatepark, ate it in the capsule.
165
The Lounge / Re: Post Your Edged Weapons Thread
« on: November 02, 2013, 10:20:14 PM »
I'm looking for a KaBar any suggestions? I think I want the smaller one for the practicality purposes.
 Tell them " Sheepdog sent you", for a little something special |
 Click this image for a little something special |
